It does not matter which brand’s miter saw you are using, the procedure for changing the blade is almost similar.
Miter saws are used in wooden works all over the world. However, it can also cut some metals like steel and aluminum.
The one reason for the replacement of the miter saw blade is rusting of the blade. Another reason might be less sharpness or dullness of the blade.
If anyone of the above situations occur, it would lessen the efficiency of your miter saw. Therefore, you need to replace your blade from time to time.
For Changing The Blade On Ryobi Miter Saw, You Need To Follow Certain Steps
- First of all, have some good safety precautions to avoid any accidents.
- Unplug the Ryobi miter saw so that it may not start during the maintenance.
- Raise the arm of the miter saw to its full height.
- Loose the cover screw of the blade bolt and move the blade guard up to expose the blade.
- Now, you use the blade wrench to remove the blade bolt.
- Remove the outer blade washer and leave the inner blade washer at its place.
- Remove the old blade and put the new blade at its place.
- Put the outer washer and tighten the blade bolts.
When To Replace Miter Saw Blades
The need for the replacement of the blade arises when you observe the dullness of your blade.
If you want to cut a harder material and you think that the already adjusted blade will not be able to cut that material, again you go for the replacement of the blade.
If the blade gets rusted due to rainwater, it will not cut materials properly. So, in this case, you need to replace a new blade for increasing the efficiency of your miter saw.
Apparatus Required For The Replacement Of Blade
To perform the replacement of Ryobi miter saw blade, you should have these things available with you:
- Screwdriver
- 10-millimeter wrench
- Machine oil
- Safety equipment
Step By Step Guide – How to Change Blade On Ryobi Miter Saw
If your miter saw is not cutting the materials properly, you must change your blade for better performance.
Also, if the need arises, you can change both the blade guard on Ryobi miter saw and blade on Ryobi table saw.
But here we will only teach you how you can change your blade on Ryobi miter saw. It requires a certain stepwise procedure to be followed:
Step-1: Take Good Safety Precautions
For changing the blade on the Ryobi miter saw, the first step is to take some good security precautions.
Dealing with the blade is always risky, so you should wear a mask and a pair of gloves before starting the replacement procedure.
Most important thing is to unplug any power tool before you start its maintenance. If the blade of the Ryobi miter saw is spinning, wait for it to stop before you start working with it.
Step-2: Loose The Blade Arm
If the blade arm of the miter saw is locked and in its working position which is downward, raise the blade arm to its full height by unlocking it. This will help in exposing the blade to you.
Step-3: Remove The Blade Bolt
For removing the blade, first, you need to remove the blade bolt. So, remove the bolt cover first by moving it upward and then, loosen the blade bolt with a wrench after locking the spindle of the blade arm.
In case, the spindle of the miter saw is not locked properly, you will be unable to remove the blade bolt due to its frequent rotation.
Step-4: Remove The Blade
Once you have removed the blade bolt, now rotate the lower blade guard up to fully expose the blade.
Now, remove the outer washer of the blade and keep the inner washer at its place.
While putting the new blade, make sure to place the outer washer again at its place otherwise, it can cause an accident.
Make sure the spindle of your Ryobi miter saw is fully locked so that blade cannot rotate.
Remove the blade and give oil to the point where the inner washer and outer washer contacts with the blade.
Step-5: Fix New Blade
Now, you are all set to fix the new blade in the miter saw. After putting the new blade, put the outer washer at its place and start tightening the blade bolt of the Ryobi miter saw with a 10-mm wrench.
Make sure your blade has been fully tightened to avoid any accidental situation. Now, put the bolt blade cover on the blade arm and lower the blade guard ring.
Make sure to unlock the spindle before plugging in the Ryobi miter saw. Congratulations! You have replaced your Ryobi miter saw blade successfully.
Overview
Here we are giving you a quick review of the whole article. To perform the replacement of the Ryobi miter saw blade, you need to be aware of certain crucial things.
Moreover, you have to follow the above-discussed steps one by one. First of all, take good safety measures to work safely with the miter saw.
You must unplug the miter saw to minimize the chances of getting an electrical shock.
Then, follow the rest of the procedure order-wise to change the miter saw blade successfully and safely.
FAQs
How Do I Change The Blade On My Miter Saw?
Changing the blade on a miter saw is not a complicated thing rather it is quite simple and straightforward. You only need to follow the procedure discussed below to replace the blade of the miter saw:
- First of all, have some good safety precautions.
- Remove the cover of the blade bolt and start removing the blade bolt with a 10-mm wrench.
- Move the guard of the blade upwards to expose the blade.
- Remove the outer washer of the blade and remain the inner washer at its place.
- Remove the blade safely and put the new one in its place.
- After placing the new miter saw blade, do not forget to put the outer washer again at its place.
- Tighten the blade bolt again and lower the guard of the blade.
- Unlock the spindle before plugging in the miter saw.
How To Change Ryobi 7-1/4 Miter Saw Blade?
The procedure for the replacement of any kind of blade on a miter saw is almost the same whether it is a 7-1/4 inches miter saw blade or any other. You have to follow certain steps to change the Ryobi 7-1/4 miter saw blade.
After having good safety measures, remove the cover of the blade bolt and then remove the blade bolt. After this, remove the outer washer and pull out the blade. Install the new blade at its place and after putting the outer washer, tight the blade bolt firmly. In the end, lower the guard and unlock the spindle.
How To Replace The Guard On The Ryobi Miter Saw?
Replacing the guard on Ryobi miter saw is very easy. You need a screwdriver to remove the guard from the guard assembly. After removing it, place the new blade guard and tighten the bolts firmly with the help of a screwdriver.
How To Change The Blade On The Ryobi Table Saw?
There are two blades on a miter saw, one on the blade arm and the other on the table of the saw. Changing the blade on the Ryobi table saw is a very simple process.
You have to put the wrench in the table saw to remove the blade bolts. After that, you have to remove its outer washer and then remove the blade carefully. Then, put the new blade at its place and install the outer washer on it. In the last, tight the bolts of the blade firmly.
Are Miter Saw Blades Reverse Threaded?
Reverse threaded blades are the one which rotates in the counter-clockwise direction. The blades of the miter saw rotate in an upward direction. If you see it from the right side, you will realize that the blade is running clockwise. And from the left side, it looks as if the blade is running counter-clockwise that is reversely threaded.
So, we cannot say whether the miter saw blades are reverse threaded or not because it depends upon the direction from where the viewer is watching.