In this we learn how to cut baseboard with miter saw. Everything has a proper way to deal with it; this might not be as same as cutting the crown mold as it has its adjustment and means to sell it.
Today we are going to discuss how to cut baseboard with miter saw properly by using a miter saw. To do that, we will divide this into various steps so that you will not confront much difficulty.
Some of us might already know that the installation of the baseboard is not as tricky or effort requiring as cutting them with accuracy.
Everyone can cut through a baseboard, but cutting with the right adjustment and accurately is what makes us professional.
However, this is also a matter of practice; more you practice better, you will become to cut through it with the miter saw.
How To Cut Baseboard With Miter Saw Properly:
We cannot deny the importance of devices and tools, and you cannot go to war without your weapons, to get started to get yourself essential tools which are:
- Miter saw
- Dust mask
- Measuring tape(to measure the adjustment)
- Protective wear(goggles etc.)
Another important thing before we get started is you must know the parts of your miter saw. If you have not checked it thoroughly yet, then make time and get yourself familiar with your miter saw, such as the degree of the angle, bevel angle, and the miter angle, etc.
Start With Measurement:
To cut your baseboard correctly, you need to be accurate with measurements, first, make sure you get the right side of the wall on which you want to adjust the baseboard.
Mark the measurement on baseboard using pencil, if you notice that length is by the corner, you can adjust the blade on 45 degrees so it will become easy for you.
It is always important to first go through the right measurement before making cuts, now that you have taken your measurement and adjusted the blade it is now time to cut through your baseboard.
Cutting The Baseboard Using A Miter Saw:
As we know that sometimes, things might seem tricky more than they should, the cutting baseboard would look difficult too, but it is not in reality.
Get your dust mask and safety goggles on, place your baseboard on a miter saw, it should stand on the edge, and black flush would be leaning on the fence.
Now place the baseboard and start cutting the face-off, but note that it would be if you are making an inside cut while making the outside cut you need to cut off the back and make sure your baseboard is held firmly against the fence.
Making An Inside Corner:
To cut the inside edge of a baseboard, you need to make four inside corner cuts. First, adjust the miter and the bevel angles to zero, having 45 degrees.
You need to mark the opposite side of the baseboard with a pencil for accurate measurement. Now cut according to the mark of your pen. You also need to consider that the back of the baseboard is longer than the front side.
Lower the miter saw on the board and push the blade down, once you are done cutting it switch the miter saw off and raise the edge, do not put extra weight over your miter saw while cutting, as it might give you invalid baseboard cutting:
Some people, while working with a miter saw, do not notice the force they are applying on the blade of the miter saw.
It usually damages their baseboard and ruins the whole thing, it is, of course, not difficult, and you can achieve with practice, but you need to take care of the force you are applying.
How To Make An Outside Corner Cut?
It is not very difficult to cut on the outer corner sides of your baseboard; you need to learn the right technique.
From the previous topic section we know how to cut through our baseboard from the inside corners, and you can let your baseboard just the way it is.
You even do not have to make any alteration, what you need to do is to mark the outside corners on the back of the baseboard, you can mark it with the pencil you have.
After that, you can start cutting the baseboard. The only difference which you should keep in mind is that your front baseboard should be longer than the back part of it.
How To Make The Square Cut Using A Miter Saw?
A square-cut depends on what type of cut you want from it; if for some reason your baseboard needs to stay adjacent to the other baseboard, then you are in need to have the square cut.
However, this is not difficult, and you can cut it with a little bit of practice. To do that, make sure your miter saw angle is set first to zero degrees, zeroization is essential, and then you can move along with your cutting process.